极低压下两相流挤压油膜阻尼器油膜参数特性

针对极低供油压力工况开展实验研究,以考察气液两相流对挤压油膜阻尼器(SFD)油膜参数特性的影响。结果表明:当SFD入口气体体积分数小于0.9时,油膜阻尼随着入口气体体积分数的增加而减小,直至气体体积分数增大到0.9时,油膜阻尼是纯油状态时阻尼的60%;当气体体积分数大于0.9时,油膜阻尼大幅减小至几乎可以忽略不计。现有理论模型并不适用于极低供油压力工况。基于实验结果,找到了最符合SFD两相流动的等效黏度模型,其理论预测的油膜阻尼与不同供油压力下的实验数据吻合较好,为SFD两相流研究的模型选择提供了依据。     

基于非接触式测量的旋转叶片动应变重构方法

基于叶端定时非接触式测量和振动响应传递比的概念,开展高速旋转叶片动应变重构方法的研究。在频域内推导了叶片任意测点位移与任意测点动应变的传递比,给出了单模态共振下响应传递比关于位移和应变模态振型的解析表达式;建立旋转叶片的三维(3D)有限元模型,开展考虑旋转预应力效应的叶片模态分析,提取位移和应变模态振型,获得任意转速下叶端位移与叶根关键点动应变的传递比。开展高速旋转叶片叶端定时非接触式测量实验,采用周向傅里叶算法对叶端定时信号进行处理,获得叶片在不同转速单模态共振下的叶端位移,结合响应传递比,重构5个旋转叶片的关键点动应变。结果表明:旋转叶片在9000r/min和13000r/min转速下发生1阶共振时,与应变片实测结果相比,叶根处应力最大点、次大点和边缘点3个关键点的动应变平均重构误差均小于15%,验证了旋转叶片动应变重构方法的有效性。     

航空活塞二冲程发动机的可变排气阀换气过程

航空活塞二冲程发动机的换气过程直接影响发动机的性能,采用可变排气阀可以改善发动机的动力性能。通过GT-Power软件搭建发动机一维整机模型,进行可变排气阀的仿真研究,分析了发动机在不同转速、不同排气阀状态下的换气过程及排气阀状态对换气过程的影响。在此基础上,还对定速巡航工况下(6500r/min转速、50%节气门开度)的排气阀状态进行了优化。结果表明:不同的排气阀状态可以改变发动机排气过程压力波动的相位,从而影响发动机的换气品质及燃烧过程;在定速巡航工况下,排气阀为中等开度时(初级阀关闭、次级阀开启),其发动机动力性能达到最优。     

主流攻角对双射流孔气膜冷却特性的影响

应用压力敏感漆技术,在平板上测量了不同主流攻角(i=-30°,-20°,-10°,0°,10°,20°,30°)下双射流孔的气膜冷却效率,并利用计算流体动力学(CFD)计算得到的流场对气膜冷却效率的规律进行了解析。所研究的双射流孔结构的孔间无量纲横向距离为0.5,孔间无量纲流向距离为3;射流与主流密度比为1.0,吹风比分别为0.5、1.0、1.5、2.0。结果表明小的主流攻角(i=-10°,0°,10°)下,流场中存在反肾型涡对或挤压作用,气膜层与壁面贴附良好,气膜冷却效率最高;大正值攻角(i=20°,30°)下,虽然气膜覆盖面积大,但反肾型涡对退化,气膜冷却效率下降;大负值攻角(i=-20°,-30°)下,流场中有肾型涡对,且气膜横向覆盖受限,气膜冷却效率最低。     

盘腔进气位置对径向预旋系统的影响

为减少径向预旋系统的流动损失,运用数值模拟方法对不同盘腔进气位置的径向预旋系统进行分析,结果表明:随着盘腔进气径向位置的增加,预旋喷嘴出口气流旋流比随之逐渐减小,径向预旋系统的温降系数及总压损失系数均随之逐渐增大。当旋转雷诺数等于7.9×106,盘腔进气位置由低位向高位变化时温降系数最大可增加525%,同时总压损失系数增加3.93%。径向预旋系统内比熵增主要发生在预旋喷嘴和共转腔,约占系统总体比熵增的80%。随着盘腔进气径向位置的增加,径向预旋系统总体比熵增降低,预旋喷嘴比熵增占比逐渐增大,共转腔比熵增占比逐渐减小。     

Aerodynamic optimization design for high pressure turbines based on the adjoint approach

A first study on the continuous adjoint formulation for aerodynamic optimization design of high pressure turbines based on S2surface governed by the Euler equations with source terms is presented.The objective function is defined as an integral function along the boundaries,and the adjoint equations and the boundary conditions are derived by introducing the adjoint variable vectors.The gradient expression of the objective function then includes only the terms related to physical shape variations.The numerical solution of the adjoint equation is conducted by a finitedifference method with the Jameson spatial scheme employing the first and the third order dissipative fluxes.A gradient-based aerodynamic optimization system is established by integrating the blade stagger angles,the stacking lines and the passage perturbation parameterization with the quasi-Newton method of Broyden–Fletcher–Goldfarb–Shanno(BFGS).The application of the continuous adjoint method is validated through a single stage high pressure turbine optimization case.The adiabatic efficiency increases from 0.8875 to 0.8931,whilst the mass flow rate and the pressure ratio remain almost unchanged.The optimization design is shown to reduce the passage vortex loss as well as the mixing loss due to the cooling air injection.     

An equivalent ground thermal test method for single-phase fluid loop space radiator

Thermal vacuum test is widely used for the ground validation of spacecraft thermal control system. However, the conduction and convection can be simulated in normal ground pressure environment completely. By the employment of pumped fluid loops’ thermal control technology on spacecraft, conduction and convection become the main heat transfer behavior between radiator and inside cabin. As long as the heat transfer behavior between radiator and outer space can be equivalently simulated in normal pressure, the thermal vacuum test can be substituted by the normal ground pressure thermal test. In this paper, an equivalent normal pressure thermal test method for the spacecraft single-phase fluid loop radiator is proposed. The heat radiation between radiator and outer space has been equivalently simulated by combination of a group of refrigerators and thermal electrical cooler(TEC) array. By adjusting the heat rejection of each device, the relationship between heat flux and surface temperature of the radiator can be maintained. To verify this method,a validating system has been built up and the experiments have been carried out. The results indicate that the proposed equivalent ground thermal test method can simulate the heat rejection performance of radiator correctly and the temperature error between in-orbit theory value and experiment result of the radiator is less than 0.5 C, except for the equipment startup period. This provides a potential method for the thermal test of space systems especially for extra-large spacecraft which employs single-phase fluid loop radiator as thermal control approach.     

超声速串列静叶积叠优化分析

在进口超声速、气流转折角大的高负荷条件下,静叶通道中激波强度高,激波、附面层干扰引起的损失大,且静叶中三维流动引起的径向载荷分布不均匀,易产生角区分离。叶片积叠优化是提高风扇性能的一项有效技术。采用数值模拟的方式研究了不同积叠形式对优化串列静叶沿展向激波结构,改善叶排间流动匹配的作用。三维流动对比分析可以得出:高负荷串列静叶采用正弓形积叠,叶片展向载荷分布合理,静叶端壁角区分离损失减小,前后叶片排流动匹配较好,风扇性能进一步提高。     

基于结构动力学特性的损伤识别方法

基于等效模态应变/动能理论,提出了一种利用实际结构的测试数据识别结构中损伤位置的方法。在此基础上,研究了利用模型修正技术识别结构中损伤强度的方法。分别以一个单损伤平板结构和多损伤平板结构为例,通过仿真分析了以上方法的有效性。结果表明,以上方法可以有效识别结构中的损伤位置和损伤强度。     

飞机液压系统动态油温计算方法优化

分析了动态油温计算方法的不足,将此方法中的液压油箱计算模型加以优化得到改进的动态油温计算方法,基于功率损失法给出了飞机液压系统中四种典型液压附件的温度计算方程。以某航空液压泵地面试验系统为计算实例,将改进方法计算的结果与试验结果、改进前方法的计算结果进行对比分析,结果表明改进的动态油温计算方法相比改进前的方法具有更高的准确度。